Important Notice!

 

Dear Customer: Please read the rope cord instructions for proper rope assembly and care of your Hyperformance Buddy Lee Jump Rope!

 

30-DAY WARRANTY POLICY AFTER PURCHASE!

 

We stand behind our products and all products are guaranteed against manufacturing defects in materials and workmanship. Within the 30-day warranty, we will repair and/or replace parts or products that are defective in materials or workmanship. You must email a picture and a proof of purchase.

 

HOW TO PRESERVE THE LIFE OF YOUR JUMP ROPE CORD & SWIVEL BEARINGS!

 

1.    First adjust the rope for your height (see back of this sheet)!

2.    During jumping, the jump rope should barely skim the surface, and not slam into it. If it does, adjust further.

3.    Hang rope over a hook to let it straighten out. OR you can also keep it lying loosely in a workout bag. Do not wrap it around the handles. When jumping, if you are using correct form and the cord has been adjusted, the arc will straighten as you are jumping.

4.    Avoid jumping in or storing the jump rope in cold temperatures such as a garage or in the trunk of a car. It will make the cord stiff and can also cause it to break when jumping.

5.    Avoid jumping on concrete as it can wear the cord out. Jumping on other hard surfaces such as tile can also cause undue stress to your joints and/or shin splints.

 

YOU MAY LUBRICATE SWIVEL BEARINGS WITH OIL SUCH AS WD-40, TEFLON OIL OR OTHER OIL FOR DURABILITY AND A SMOOTH TURNING MOTION!

 

PLEASE NOTE: The swivel bearings and rope cords are replaceable in order to help maintain years of High performance. The swivel bearings are designed primarily for Hyperformance speed and control with no rope tangle and will wear out quicker than conventional jump ropes.

Please refer to our ONLINE STORE to order our replaceable swivel bearings and rope cords.

Thank you and keep on Jumping!

 

Each Buddy Lee Jump Rope comes with instructions for adjustment.

It is located on the inside of the backing card.

 

JUMP ROPE MEASUREMENT & ADJUSTMENT!

 

The tip of the handles should reach to shoulder for standard length OR to the underarm (as in the picture) for skilled jumpers.

 

During jumping, the rope cord should barely skim the surface, and not slam into it. If it does, adjust further.

 

If the rope is for a young person who is still growing, it is best to leave a little extra cord and tie a knot or two on each side, so he/she doesn't grow out of it right away.

 

Swiwel Bearing Rope Adjustment

Tools needed for adjustment: Scissors

 

1.    Screw the cord into one handle.

2.    Stand on center of cord with one foot.

3.    Pull cord up alongside body, until tip of handle reaches to shoulder or underarm (see picture above).

4.    Cut the free end of the cord.

5.    Screw the other handle in.

 

Magic Speed Rope Adjustment (with Eyelets)

Tools needed for adjustment: Pliers & Scissors

1.    Stand on center of cord with one foot.

2.    Pull cord up alongside body. Tip of handles should reach to shoulder or underarm (see picture above).

3.    To adjust, pull cord through back of one handle.

4.    Then use pliers to uncrimp 1st eyelet.

5.    Slide eyelet down to desired length and secure by recrimping it.

6.    Cut off the excess cord.

7.    Check the eyelets before each jumping session to make sure they are secure.  

 

                   

International Distributors, Buddy Lee Jump Ropes

Trainers
Sign up
Join our mailing list and be the first to hear about all our updates & offers!
We respect your privacy

We never sell, share or rent your personal information to any third parties under any circumstances. We may share information with governmental agencies or other companies assisting us in fraud prevention or investigation. We may do so when: (1) permitted or required by law; or, (2) trying to protect against or prevent actual or potential fraud or unauthorized transactions; or, (3) investigating fraud which has already taken place. The information is not provided to these organizations for marketing purposes.